Results 1 to 14 of 14

Thread: "Go Mai" Camp Chopper WIP

  1. #1
    Senior Member
    Join Date
    Jan 2012
    Location
    Pittsburgh PA
    Posts
    261

    Default "Go Mai" Camp Chopper WIP

    I have recently been very inspired by the work of Claudio Sobral and his harpoon points in particular, if you haven't seen his work you need to check it out! This recent inspiration resulted in the idea for a "go mai" harpoon point, go mai being five layers (if I have that correct) as opposed to san mai which has three. I had some left over 700 layer PW billet put together from 15N20, 1084, and 1095; I thought this would be the perfect core for this camp chopper and decided to give it a go.

    Here is the concept drawing:

    Guests can not see images in the messages. Please register in the forum.

    In this drawing the blade is 1 3/4 inches wide and 7/34 inches long.

    After getting the image in my head on paper I was able to tack a billet together. For the center core I cut the remaining PW billet in half and stacked it together to achieve the appropriate thickness for the core. I then placed a 1/8 inch piece of 15N20 on either side and placed two pieces of 1/4 inch W2 on either side of the 15N20. Because the PW billet is the same material being welded to its self I am treating it as "1" layer instead of two resulting in "five" layers.

    Guests can not see images in the messages. Please register in the forum.

    I then welded the billet together and ground the edge to check for weld flaws:

    Guests can not see images in the messages. Please register in the forum.

    A quick etch to see if everything is centered. (On one side of the billet there was a small portion of the original PW billet that had a heavy hammer mark in it. In this photo it looks like a weld flaw but is not and came out later on in the forging process.

    Guests can not see images in the messages. Please register in the forum.

    I then drew out the billet, forged, and profiled the blade. (Sorry I didn't get any photos of the steps in between). :

    Guests can not see images in the messages. Please register in the forum.

    I then rough ground the blade:

    Guests can not see images in the messages. Please register in the forum.

    At this point I leave the plunge lines rough as I will refine them with files later on.

    A quick dip in acid to see what is going on:

    Guests can not see images in the messages. Please register in the forum.


    Then after much polishing (5 hours 37 minutes and 15 seconds of polishing) I ended up with this:

    Guests can not see images in the messages. Please register in the forum.

    Guests can not see images in the messages. Please register in the forum.

    Guests can not see images in the messages. Please register in the forum.

    Guests can not see images in the messages. Please register in the forum.

    I have been experimenting with this "grunge" look while etching. After polishing to 2000 grit and buff I etch it briefly and then scuff it with 320 grit in random places to let the acid eat in more deeply in those places. I know this look isn't everyone's cup of tea but I like it in certain styles, this effect worked better on one side then the other, but overall I am pleased with how this blade is coming out.

    More photos to follow. Thanks for looking.

    Robert


  2. #2
    Super Moderater RangerXanatos's Avatar
    Join Date
    Mar 2008
    Location
    Northeast, Georgia
    Posts
    1,970

    Default

    That is beautiful!
    What's so crazy about standing toe-to-toe saying I am?
    ~Rocky Balboa

  3. #3
    Senior Member MrFixIt's Avatar
    Join Date
    Jan 2014
    Location
    Bogart, GA
    Posts
    1,093

    Default

    Can't wait to see the finished product!
    When all else fails, read the directions, and beware the Chihuahuacabra!

  4. #4
    Senior Member
    Join Date
    Jan 2012
    Location
    Pittsburgh PA
    Posts
    261

    Default

    Thanks for the comments everyone. Today was mostly about fitting the guard and would have taken up most of the day except I could sleep last night (up at 3:30 am) and so I was done fitting it by 7:30

    Thankfully though I was using bronze which is so wonderfully soft and not as much of a pain as filing stainless. I started with a 1/2 inch bar and cut away the excess then I started fitting it.

    Initial fit:

    Guests can not see images in the messages. Please register in the forum.

    Getting closer:

    Guests can not see images in the messages. Please register in the forum.

    And when I'm just under 1/16 inch away I stop and start to make the shield. In this case it was textured copper:

    Guests can not see images in the messages. Please register in the forum.

    Guests can not see images in the messages. Please register in the forum.

    I then "strippled" The bronze using my dremel and antiqued it using sulphur dioxide and a couple of pass with my propane torch.

    Guests can not see images in the messages. Please register in the forum.

    Somehow I completely forgot to take pictures of the handle fitting, but I was able to get it on and shaped today. It's finally starting to look like a knife and a pretty decent one at that. There is still a good bit of clean up work on the handle, marking the blade, and the sheath but it's definitely getting closer. I will be working on the sheath tomorrow but for now I have to go clean the house for book club
    Thanks for looking!

    Guests can not see images in the messages. Please register in the forum.

  5. #5
    Administrator Rick's Avatar
    Join Date
    Nov 2007
    Location
    Central Indiana
    Posts
    58,832

    Default

    That's a pretty amazing transformation. Had to give a some rep.

  6. #6
    Senior Member hunter63's Avatar
    Join Date
    Jul 2009
    Location
    SE/SW Wisconsin
    Posts
    26,866

    Default

    That is quite a project....very nice....I like it.
    Thanks for posting.
    Geezer Squad....Charter Member #1
    Evoking the 50 year old rule...
    First 50 years...worried about the small stuff...second 50 years....Not so much
    Member Wahoo Killer knives club....#27

  7. #7
    Senior Member Winter's Avatar
    Join Date
    Aug 2010
    Location
    SE Alaska
    Posts
    3,171

    Default

    Wow, cool.
    I had a compass, but without a map, it's just a cool toy to show you where oceans and ice are.

  8. #8
    Super Moderator crashdive123's Avatar
    Join Date
    Jan 2008
    Location
    North Florida
    Posts
    44,846

    Default

    Great looking knife and WIP.
    Can't Means Won't

    My Youtube Channel

  9. #9
    Senior Member
    Join Date
    Jan 2012
    Location
    Pittsburgh PA
    Posts
    261

    Default

    Thanks everyone. Okay so today was about finishing the handle and making the sheath. I ended up adding a pin (not recommended to ever do at this stage, but if you are careful you can do it.) and I finalized the finish on the handle.

    First the sheath:

    I decided I would do another fold form copper inlay so I started with a 12 inch x 4 inch sheet of 1/16 copper. This part is always fun because you can just go crazy with texture development. Once it is as textured and folded as I thought looked good I covered it in a thin layer of sulphur dioxide and exposed it to heat for about 30 seconds. This is the result.

    Guests can not see images in the messages. Please register in the forum.

    Pretty ugly looking but it will get better. From this piece I will trim my inlay. But first I make a paper pattern over the the top layer of the sheath to determine size and pleasing shape. It's important when doing any inlay to remember to leave room for your stitching.

    Guests can not see images in the messages. Please register in the forum.

    Then carve out the design in the leather to allow the copper to fit "flush" with the surface. (I am using 4 ounce leather on the top face of the sheath)

    Guests can not see images in the messages. Please register in the forum.

    I then cut out an interesting section from the copper sheet to use as the inlay.

    Guests can not see images in the messages. Please register in the forum.

    The leather is then dyed and the copper inlay is glued in and pressed flat with a weight.

    Guests can not see images in the messages. Please register in the forum.

    I then punched all of the holes.
    Guests can not see images in the messages. Please register in the forum.

    And then you just stitch everything together:

    Guests can not see images in the messages. Please register in the forum.

    And the finished sheath:

    Unfortunately not the best picture but better photos are to come.

    Guests can not see images in the messages. Please register in the forum.

  10. #10
    Administrator Rick's Avatar
    Join Date
    Nov 2007
    Location
    Central Indiana
    Posts
    58,832

    Default

    That is uber cool. You, sir, are an arteest. (That's way more avant-garde).

  11. #11
    Senior Member
    Join Date
    Jan 2012
    Location
    Pittsburgh PA
    Posts
    261

    Default

    I lucked out on lighting at the end of the day and was able to snap some good photos showcasing the new camp chopper.


    Guests can not see images in the messages. Please register in the forum.
    Last edited by Scottishsmith24; 09-06-2014 at 07:37 AM.

  12. #12

    Default

    Daum! Nice craftsmanship!

  13. #13
    Senior Member
    Join Date
    Jan 2012
    Location
    Pittsburgh PA
    Posts
    261

    Default

    Thanks ElevenBravo!

  14. #14
    Administrator Rick's Avatar
    Join Date
    Nov 2007
    Location
    Central Indiana
    Posts
    58,832

    Default

    I see you redid the sheath. I didn't think the knife was going to fit in that first pic.





    Bazinga!

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •