View RSS Feed

Beo

Tuning a Flintlock

Rate this Entry
Tuning A Flintlock: Continued

PANS, POWDERS AND PRICKS
Priming the pan - The pan should never be filled to the point where powder covers the touch hole. If the touch hole is covered, powder will have to burn down until it uncovers the touch hole before the main charge can ignite. The key is to be sure that the touch hole is clear so that the hot gas flash can get through the touch hole to the main charge. A technique used is to carefully place the charge away from the hole and not fill the pan completely(1/3 to 1/2), then to tap the rifle on the lock side just before firing to jar the powder away from the touch hole. Several late flintlock period manufactures even sloped the cavity in the pan slightly away from the touch hole. For quicker ignition use the least amount of powder that will ignite your main charge. Experiment to determine this amount.
Powder used in priming and should be 4F or finer although I use 3F. Fine powder ignites easier/quicker.
Vent Pricks serve two very important purposes. One is to clear the vent of debris, the second is to open a channel for the hot gas flash to the main charge. For reliable ignition it is common practice to insert the vent prick just before priming the pan and closing the frizzen. Some also force a small amount of priming powder into the vent with the prick, being sure to insert the prick at the finish, far enough so that the open channel is maintained. Since fine powder ignites easier, this small amount can't hurt and actually helps ignite the main charge. You are not trying to create a powder train. You are trying to place a few grains of fine powder into the surface of the channel that you created in the powder with the prick. You are not reducing, blocking or changing the channel in any way. Try it both ways and use what works for you, the important point here is to keep that flash channel open! Vent pricks made of bronze welding rod are recommended because bronze won't wear the metal in the touch hole like a steel prick will. Pricks that have 4 sides work well as the sharp edges help clear the fouling in the touch hole.
TOUCH HOLES
Size Touch holes generally fall in the 1/16 (.0625) to 5/64 (.078) inch range. Some preferring slightly large for smooth bore. The maximum is considered to be 1/10 (0.1)
Location A straight line across the flats of the pan should split the center of the touch hole. Or if not spilt by this line be just slightly below it. A hole placed too low will tend to get covered with powder causing erratic/slow ignition, too high can also cause erratic ignition by blocking some of the heat flash. A touch hole that is too high will sometime work best with a full pan of powder, often a poorly placed touch hole will need to be replaced by a touch hole liner.
Touch Hole Liners One of the problems with a drilled flash hole is that it results in a relatively long small passage from the pan to the powder charge. Touch hole liners are used for several reasons:
a.) To replace enlarged worn touch holes. Wear and corrosion are the main enemies of your touch hole. Liners are made of hard corrosion resistant materials.
b.) To get the main charge closer to the priming gas heat flash. Touch hole liners can be drilled concave on the inside to allow the main powder charge to get closer to the outside of the barrel and create a shorter path for the hot gas to travel.
c.) To correct poor hole placement. d.) To be used as an aid in cleaning. e.) Liners allow removal so that a small amount of powder can be put behind the ball, when a ball is loaded without powder by mistake.
FRIZZENS
The sear and frizzen should work freely when their respective pivot screws are turned in as far as possible. Screw threads should not extend into the pivot area. Polish the pivot area on screws. The frizzen face should be smooth but not polished. A rough face will quickly dull flints. The frizzen should test at a Rockwell Hardness of around 56. A clean frizzen surface sparks best, wipe it often.
SPRINGS
Springs are the heart of your lock. Polish all contact points. (Examples - main spring tip, tumbler hook surface, top surface of frizzen spring.) Make sure that the nose of the mainspring has clearance in the tumbler at the fully cocked position. Polish the springs themselves, a polished spring is less apt to fracture. Any scratches or flaws are potential fracture points. Caution: polish only, do not reduce the strength of the spring. Make sure that the spring does not bind anywhere during its movement. There should be approximately a 1/3 to 2/3 balance between the main spring and frizzen spring (by feel or trigger pull gauge).
WET WEATHER
a.) Use Vaseline to seal the edges of the frizzen and the frizzen-to-barrel line. The vee where the barrel and stock or lock plate meet can channel water directly into the pan. Fill this vee for about 10 to 18 inches in front of the pan. Use wax sparingly as over waxing can hinder lock speed, especially in cold weather.
b.) Change priming powder frequently.
c.) Use a Cow's Knee cover during wet weather.
d.) Carry in a manner to protect the lock from the weather.
Hope this helps with the questions I have been asked about how I tune my flintlock and yes this is really just general maintence to me.
Good shooting and aim small, miss small.
Beo,

Submit "Tuning a Flintlock" to Digg Submit "Tuning a Flintlock" to del.icio.us Submit "Tuning a Flintlock" to StumbleUpon Submit "Tuning a Flintlock" to Google

Categories
Uncategorized

Comments