Making Tallow Candles

[rwc1969]

I took the hard fat from my deer and rendered it down to make tallow. Tallow is hard like wax and can be used for all sorts of things from candles to wood, bone and leather preservative. You can use it to waterproof your boots or make soap. You can cook with it. Rendering is a process which takes fat which would otherwise go rancid and removes impurities, this keeps it from going rancid.

The first thing you need to do is remove the hard fat from your deer or other animal. Fat from deer, sheep, beef and bison is considered tallow while fat from pigs is considered lard. Lard is much softer than tallow, but the process is the same for either.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/01Fat.jpg

Next, I cut mine into 1" or so cubes. Now is the time to remove any chunks of meat, tendon or the like that you don't want in the mix. I removed the large chunks of meat, blood, tendon and sinew and left the rest.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/02Cubes.jpg

This next step is optional, but should speed up the rendering process. Grind it up!

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/03Grind.jpg

I also weighed mine to get an idea of how much fat and such it takes to make a pound of tallow. If I recall correctly I had just over 1-3/4 pounds of fat and scraps.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/04Weigh.jpg

There are three ways to go at this point. I chose to boil because it is safer and prevents overheating. I added it to a pot and added just enough water to cover it.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/05CoverWithWater.jpg

Bring it to a boil and immediately reduce to a simmer. Let it simmer until the fat oozes out, 1/2 to 1 hour should be plenty of time if you grind it. I let mine go for 1 hour. If you didn't grind you will probably want to use a potato masher or the like to squish out the fat from the chunks as it simmers. Don't let it boil over or slop out, it will catch fire and/ or splatter if it hits the burner.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/06BoilAndSimmer.jpg

Once you feel all the fat has seperated immediately strain it through a fine a mesh strainer. Don't let any go down the sink or it will plug it up and be careful not to burn yourself. If you haven't ground the fat you'll want to squish the bits with the potato masher to get the remaining fat to run through.

The strainer bits can be fed to the birds, cats, or dogs. They'll love it. If the fat was fresh you can eat it yourself. If you had simply fried out the tallow without water and without grinding you would now have cracklins. People eat this stuff. I tasted some and it had no real flavor and was the consistency of overcooked hamburger.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/07StrainAndFeed.jpg

Now, let it cool off to room temp and refrigerate overnight. You actually don't have to refrigerate it, but it goes quicker if you do.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/08Cool.jpg

In the morning you'll have this...

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/09UntilHard.jpg

Slide a knife or something down beside it to loosen and lift it out. Mine was already loose so I just reach in and grabbed it. It weighs about 1-1/2 pounds now.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/10Thickness.jpg

As you can see, it will have some grizzle/ cracklin bits that made it through the colander on top, and loose bits on the bottom. Rinse it off with cold water. Some bits will stay, that's ok. By the way, hot water will melt it. Dry it off completely with a towel.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/11Impurities.jpg

Now you can get rid of the water and bits that settled out. I wouldn't put them down the sink, but feed to the dogs or cats. It is full of nourishment that they otherwise would not likely get. It's essentially a really rich beef or, in this case, venison broth.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/12FeedWaterPlugDrain.jpg

Now, break it up into a small pan, place that pan in a larger pan filled partway with water. Let it melt. Be careful not to boil the water over and watch out for splattering from any moisture left in it. It will burn you. Let it go until any retained moisture is evaporated off. Be careful not to spill the meted tallow, it will ignite if it hits the burner.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/13Reheat.jpg

Let it cool slightly and pour it through a coffee filter into a dry heat safe container to get rid of the small bits that didn't settle out earlier. It needs to be pretty warm to run through the filter, don't burn yourself or melt the filter. If you pour it into glass that is wet or not heat safe it will likely break the glass. I use dry canning jars.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/14FilterWhileWarm.jpg

Let it set up once more and it is now rendered safe, it will not go rancid. If you used sterilized equipment you can supposedly let the jars seal and store it in the cupboard. I'm storing mine in the refrigerator.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/15Store.jpg

Now you can make candles and stuff. Here, I used a sliver of false tinder fungus as a wick and added some Nutmeg and vanilla to give it a pleasing scent. It has a lower melting point than wax, your body heat will melt it. But, if filtered well it burns fairly clean and long with no noticable scent.

http://i101.photobucket.com/albums/m50/shroomer69/Bushcraft%20in%20Michigan/16Candle.jpg

That's it! Here's a video that shows the entire process. It's real easy to do, but you have to be careful not to burn yourself or catch something on fire.

http://www.youtube.com/watch?v=mYU8uVmzX5E

[crashdive123]

Great tutorial. A little rep sent your way.

[ravenscar]

what is the estimated time it can last in storage?

[your_comforting_company]

I stored mine in a butter tub out in the shed, for a year now. While mine did go moldy and get a bit of a smell, it still works fine for fuel.
If stored and cleaned as well as RWC has done here, I'd imagine it would keep for several years.

I've never tasted deer cracklins before, but I eat pork-skins a lot. Next time try them with a little salt and pepper and let me know how those deer cracklins taste!

Another great tute RWC! Nice work!

[rebel]

Great tutorial!

[Rick]

I did much the same with pork fat.

http://www.wilderness-survival.net/forums/showthread.php?t=6729&highlight=bacon+candles

I have 3 pints of rendered lard that have been sitting on the counter for seven months and I've seen no noticeable change. Remember that when fat goes rancid it is simply oxidizing and not rotting. Unless it takes on an objectionable order it will still be perfectly usable for something like candles. It's probably even safe to eat but here's another instance in which I'm not going to be the guinea pig. If it begins to smell then you probably do have some microbial action going on.

Another really great tutorial, RWC. Once you've boiled the tallow why couldn't you simply strain it? That would bypass a couple of steps but arrive at the same location I think. You'd have tallow mixed with water and the bits removed by the filter.

I'm not questioning your method just trying to understand your process. As I said, another great tut. More rep your way!!

[Justin Case]

Nice Post rwc,, Rep sent,,

So when all is done, do you basically have lard ? or is it as firm as wax ?

[Batch]

Even if you don't hunt you can use the same process described above with bacon grease or other captured animal fat.

We always called cracklin the smaller harder pork rinds. Now, the call pork rinds pork skins.

I prefer Baken-ets hot-n-spicy fried pork skins over any home made ones I have ever tried. Lots of latin people make chicharrones. Which is the same thing only harder to say and eat. LOL

[Rick]

I'll let him speak to the tallow but in the case of lard you have a solid material with a consistency something like pudding at room temperature. Remember the tallow or lard is inside the animal (you and me) so it has to be very pliable or we couldn't move. In my case, I'd be a rock.

The lard turns to liquid at the slightest touch so it doesn't take much heat at all to convert it.

[Justin Case]

So lard wouldn't make a very good candle,, (unless its really cold),,

[Justin Case]

Even if you don't hunt you can use the same process described above with bacon grease or other captured animal fat.

We always called cracklin the smaller harder pork rinds. Now, the call pork rinds pork skins.

I prefer Baken-ets hot-n-spicy fried pork skins over any home made ones I have ever tried. Lots of latin people make chicharrones. Which is the same thing only harder to say and eat. LOL

Yes, those are good,,, great with beer ! :)

[Rick]

Actually, it makes a great candle. Like RWC said, once processed it's odor free, which was a surprise to me, and melts easily so you have a liquid feeding the wick much like a kerosene lamp. The key is the wick material. In my link you'll see I used two wicks. A little experimentation and a nice candle holder to deflect wind would make a very nice candle.

[rwc1969]

Ravenscar, I can't say how long it will last, first time doing this, that's why I said "supposedly" in my OP. But, I do know that we've kept bacon grease on the stove and reused it. My papaw and mamaw used to re-use lard the same way and it never went bad even uncovered.

Rick, I strained it once to get the big bits out, let it harden and then re-heated and strained it again through the coffee filter to get the smaller bits out and any moisture. The big bits would instantly clog the coffee filter and by reheating it you also get rid of any moisture left in it. Any retained moisture will cause your candles to pop and sputter.

Lard is definitely much softer than tallow, but is essentially the same thing. In the old days when all candles were made with tallow they would add alum to the mix which made the tallow even harder I beleive or made it so it wouldn't melt at such a low temp. I'm not 100% sure of these processes as the article I read was from the 1800's and spoke of different methods and uses for tallow.

You can really dive deep into the subject if you like and find different mixes for different uses. My original thought was to do it simply as possible with the intended use as a lube, preservative and candle/ lamp oil. I'm not sure how it would work as lamp oil though since it's quite hard and only flows when melted.

anyhoo, seeing how easily it ran into the tinder fungus I made some firestarters by soaking punky poplar wood, King Alfred's cakes, Reishi and Tinder fungus in the stuff. They can now be chopped up or shaved like fatwood to be used in wet weather firestarting. But, they don't seem to take a spark as easily as fatwood does.

[rwc1969]

...do you basically have lard ? or is it as firm as wax ?

It is firm as wax, but has a melting point of 109 -114 F depending on the type of fat used and possibly other variables.

If you rub it hard with your finger it will leave an oily esidue on your finger, but it wont flat out melt.

There is a scale called the titre scale or the like that is used to determine the quality of tallow. The term tallow actually refers to a rendered fats ability to not melt until above a certain temp, that's why lard isn't tallow, because it melts at too low a temp.

If that makes any sense.

[kyratshooter]

Very good tutorial.

There is a very wide dfference betweren lards and tallow. Well rendered tallow will be very solid and will snap and break if bent.

Tallow will keep for up to two years.

It is also convertable after first molding. Tallow candles can be melted and the fat used as food, pemican, bullet lube, leather tanning or anything else that requires a different form. (I got these examples from the Lewis and Clark Journals. They used tallow candles as a convinient and useful transport form)

One of those simple skills everyone should know.

[Moonviper]

really asome post thank you.

[TheLocalOutdoorsman]

Can you eat this crap in candle form. If you were in a survival situation?

[welderguy]

Can you eat this crap in candle form. If you were in a survival situation?

I dont see why not its just animal fat . not sure of the nutrition value if any .

[Ken]

Welder, I think we have another one!

[welderguy]

Welder, I think we have another one!

we shall see :D

[Ken]

Can you eat this crap in candle form. If you were in a survival situation?

I found your first post ever on the Forums to be quite interesting, so I looked at your profile:



Basic Information

About TheLocalOutdoorsman

Biography:
I like killin stuff.
Location:
North America
Interests:
killing stuff.
Occupation:
Dont need no job.

So my answer to your question is, "Yes, you can eat crap."

[Ken]

http://fcdn.mtbr.com/attachments/off-camber-off-topic/788611d1365450993-trolling-not-problem-how-you-word-your-thread-internet-troll-620x474.jpg (http://www.wilderness-survival.net/url?sa=i&rct=j&q=&source=images&cd=&cad=rja&docid=yvrskfdyAFzQRM&tbnid=IkvmXSNMJs7AlM:&ved=0CAUQjRw&url=http%3A%2F%2Fforums.mtbr.com%2Foff-camber-off-topic%2Ftrolling-not-problem-how-you-word-your-thread-848129-2.html&ei=sPi7UffyKqjZ0QH-yoCIDg&bvm=bv.47883778,d.dmQ&psig=AFQjCNHPBIXgjpuWKPvUVKmGkFwq2kajww&ust=1371359664874481)

[welderguy]

http://fcdn.mtbr.com/attachments/off-camber-off-topic/788611d1365450993-trolling-not-problem-how-you-word-your-thread-internet-troll-620x474.jpg (http://www.wilderness-survival.net/url?sa=i&rct=j&q=&source=images&cd=&cad=rja&docid=yvrskfdyAFzQRM&tbnid=IkvmXSNMJs7AlM:&ved=0CAUQjRw&url=http%3A%2F%2Fforums.mtbr.com%2Foff-camber-off-topic%2Ftrolling-not-problem-how-you-word-your-thread-848129-2.html&ei=sPi7UffyKqjZ0QH-yoCIDg&bvm=bv.47883778,d.dmQ&psig=AFQjCNHPBIXgjpuWKPvUVKmGkFwq2kajww&ust=1371359664874481)

Is there a bait and bash a troll wiki ?

[Ken]

Is there a bait and bash a troll wiki ?

Let's write one!

[welderguy]

Let's write one!

I think we could do that!

[welderguy]

And RWC, Good post. Thanks

[Sarge47]

Can you eat this crap in candle form. If you were in a survival situation?

Your IP is out of Dodo Australia, NOT North America....You really have a town down there named Dodo? And you live there? :sneaky2: G'bye troll!

[welderguy]

Your IP is out of Dodo Australia, NOT North America....You really have a town down there named Dodo? And you live there? :sneaky2: G'bye troll!

HHHMMMM sounds like "CRAP TO ME"!!


Did ya see what i did there!!!

[Sarge47]

HHHMMMM sounds like "CRAP TO ME"!!


Did ya see what i did there!!!

Yes, and say G'bye to the nice troll!

[welderguy]

Goodby Nice troll !!!

[Ken]

*mumble* Sarge keeps takin' all of our toys away from us. :sneaky2:

[hunter63]

Man that was fast.......no time to toss 'em......

[welderguy]

*mumble* Sarge keeps takin' all of our toys away from us. :sneaky2:

I know, and this poor troll never got to reply to my welcome message i left him:(

[Sarge47]

I know, and this poor troll never got to reply to my welcome message i left him:(

Troll left right after posting his inane remark. He knew what was coming. He didn't hang around to even read the responses. Probably looking for a chick to run off with.....:innocent:

[welderguy]

Troll left right after posting his inane remark. He knew what was coming. He didn't hang around to even read the responses. Probably looking for a chick to run off with.....:innocent:

Well if he is "down for anyone " we can refer him to wildandfree

[Ken]

I know, and this poor troll never got to reply to my welcome message i left him:(

Still laughing, crying, and pizzing myself from reading it!

[welderguy]

Still laughing, crying, and pizzing myself from reading it!

Thank you, thank you very much

[Gille]

To think I fill up an old spaghetti can of bacon grease every month or two an then bag it an toss it. I should be making candles. I'm a little uncertain about what to use for wicks. Cheap and easy to get come to mind but actual material?? Nice tutorial!

[welderguy]

To think I fill up an old spaghetti can of bacon grease every month or two an then bag it an toss it. I should be making candles. I'm a little uncertain about what to use for wicks. Cheap and easy to get come to mind but actual material?? Nice tutorial!

Ive head of people making candles and using regular string.

[Sarge47]

Check this out on Creek's Web-site:

http://willowhavenoutdoor.com/featured-wilderness-survival-blog-entries/5-make-shift-urban-survival-lights-when-the-electricity-goes-down/

:thumbup1:

[Rick]

I used fiberglass wick for my bacon candles. You can purchase them on the net. They are pretty cheap. I made this tute in 2009 and the candles are still good.

http://www.wilderness-survival.net/forums/showthread.php?6729-Powered-by-Bacon&highlight=bacon%20candles

[welderguy]

I used fiberglass wick for my bacon candles. You can purchase them on the net. They are pretty cheap. I made this tute in 2009 and the candles are still good.

http://www.wilderness-survival.net/forums/showthread.php?6729-Powered-by-Bacon&highlight=bacon%20candles

Have ya eaten any of them to make sure there still good!

[Gille]

Thanks Sarge! I posted this on facebook as well under the title, "FOR BACON LOVERS ONLY"..lol bet my wife loves it!
a-romantic-bacon-scented-survival-candle/ (http://willowhavenoutdoor.com/featured-wilderness-survival-blog-entries/diy-make-a-romantic-bacon-scented-survival-candle/)

[Gille]

I read a book in my early teens about a fellow who moved as far north of a small outskirt town as he could get. (don't recall which town or what the book was called :sad ) He built his own log cabin and at some point learned to use the oil in Smelt fish (https://en.wikipedia.org/wiki/Smelt_(fish)) to make oil for lanterns. Yup it smelt fishy but the smelts back then ran thick up the rivers all over north america, plentiful and free. Smelts taste good with salt and vinegar. The smelt could also be dried as fish jerky. His dog loved them also...lol

[randyt]

I remember when the smelt ran thick, it was nothing to get a couple buckets of smelt in short order.

[Rick]

The bacon candles don't smell like bacon. They don't have much odor at all. And no, I haven't tasted them. They went rancid some time back but they still work.

[hunter63]

Picked up an antique-y candle mold last year......then found out I could get a new one form Jas. Townsend at about 1/2 have the price....LOL
Anyway mine is old.
http://jas-townsend.com/advanced_search_result.php?search_in_description=1&keywords=candle+mold&osCsid=587f88d6418562390d3ce99af2ac99ce&x=0&y=0

[finallyME]

I can't believe I missed this tutorial 3 years ago. It is a really good one. Recently I have been looking at pemmican. I think I am going to make some. I don't have any deer or elk, but there is a few local beef ranchers that have grass only beef. From my limited research online, the tallow from grass only animals (not corn) contains a lot of omega 3s. Apparently men have lived off of pemmican year round without getting scurvy.
Anyways, great tutorial.

[Cyara]

Great tutorial and helpful comments... thanks so much.